Fujitsu PRIMERGY TX1330 M4 Operating Manual Download Page 75

Page: 75 / 110

TX1330 M4

Operating Manual

Starting up

5.7.1.1

Configuring the controllers

Configure the RAID controllers using the ServerView RAID Manager.

If applicable, configure the onboard SATA controller, see

"Notes on

configuring controllers" on page 77

If applicable, configure the SAS/SATA RAID controller with MegaRAID
functionality, see

"Notes on configuring controllers" on page 77

5.7.1.2

Installing the operating system

For more information on installing the server, see the
"ServerView Installation Manager" user guide at

http://manuals.ts.fujitsu.com

under

x86 Servers

Software

ServerView Suite

Server Installation and Deployment

Open this manual.

For the remote or local installation, follow the instruction in this manual and
on the screen.

Configure the settings for the general system behavior of the server using
the Server Configuration Manager.

5.8

Configuring the server without ServerView
Installation Manager

5.8.1

Configuring the server and installing the operating
system

5.8.1.1

Configuring the onboard SAS/SATA controller

If applicable, configure the onboard SATA controller, see

"Notes on

configuring controllers" on page 77

If applicable, configure the SAS/SATA RAID controller with MegaRAID
functionality, see

"Notes on configuring controllers" on page 77

5.8.1.2

Installing the operating system

Insert the DVD for the operating system you want to install.

Summary of Contents for PRIMERGY TX1330 M4















































































































Search results

Summary of Contents for PRIMERGY TX1330 M4

Reviews:

Related manuals for PRIMERGY TX1330 M4

Brands by name

Popular brands

Fujitsu PRIMERGY TX1330 M4, Operating Manual

Search results

Summary of Contents for PRIMERGY TX1330 M4

Reviews:

Related manuals for PRIMERGY TX1330 M4

Brands by name

Popular brands