Fujitsu PRIMERGY TX1330 M4 Operating Manual Download Page 36

Page: 36 / 110

Operating Manual

TX1330 M4

Product description

3.3.2.4

Indicators on the hot-plug HDD/SSD module

Figure 10: Indicators on the hot-plug HDD/SSD module

Pos. Label

Indicator

Status

Description

Access
indicator

off

The HDD/SSD is inactive.

green on The HDD/SSD being accessed

Error
indicator

off

No HDD/SSD error detected.

orange
on

An HDD/SSD error has been
detected.
Possible causes:

– The drive is defective and

needs replacing.

– A RAID rebuild process has

failed.

– The HDD/SSD module has not

been inserted correctly.

flashing
orange
slowly

HDD/SSD RAID rebuild is in
progress. Data is being restored
after replacing a drive that has
been combined into a RAID array.

Summary of Contents for PRIMERGY TX1330 M4















































































































Search results

Summary of Contents for PRIMERGY TX1330 M4

Reviews:

Related manuals for PRIMERGY TX1330 M4

Brands by name

Popular brands

Fujitsu PRIMERGY TX1330 M4, Operating Manual

Search results

Summary of Contents for PRIMERGY TX1330 M4

Reviews:

Related manuals for PRIMERGY TX1330 M4

Brands by name

Popular brands