manualshive.com logo in svg

Fujitsu PRIMERGY RX500 S7, Operating Manual

Share
Download
Fujitsu PRIMERGY RX500 S7 Operating Manual Download Page 64

64

Operating Manual

 RX500 S7

Starting up and operation

6.1.1.3

Indicators on the control panel

Power-on indicator (two colors)

Lights up green when the server is switched ON.

Lights up orange when the server is switched OFF, but mains 
voltage is present (standby mode).

HDD/SSD activity indicator (green)

Lights up green when an internal drive (HDD/SSD or backup 
drive) is being accessed.

Global Error indicator (orange)

–

Lights up orange

 if a prefailure event has been detected that 

requires (precautionary) service intervention. 

–

Flashes orange

 if an error was detected that requires service 

intervention.

–

Does not light up

 if there is no critical event.

If the event is still acute after a power cycle, the indicator is activated 
after the restart.

The indicator also lights up in standby mode.

You can find more details on the indicated errors in the System 
Event Log (SEL), on the ServerView Local Service Panel, in the 
ServerView Operations Manager or via the iRMC S3's Web 
interface.

!

Summary of Contents for PRIMERGY RX500 S7

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands