manualshive.com logo in svg

Fujitsu PRIMERGY RX500 S7, Operating Manual

Share
Download
Fujitsu PRIMERGY RX500 S7 Operating Manual Download Page 52

52

Operating Manual

 RX500 S7

Hardware installation

One optional video connector (1), one optional Front LAN connector (2) and two 
additional USB connectors (3) are located on the front of the server (

figure 3

):

Figure 3: Front side connectors

I

If components with large power requirements (e.g. external USB hard 
disk drives) are connected simultaneously, these USB connectors may 
be switched off.

Connecting the keyboard, mouse and monitor

Ê

Connect the monitor, the keyboard and the mouse to the standard ports of 
the server (see figure

2 on page 51

).

Ê

Connect the power cord of the monitor to a grounded mains outlet of the in-
house mains and/or to the mains socket strip of the rack.

V

CAUTION!

The rated current for the monitor is indicated on the technical data label 
on the monitor or in the operating manual for the monitor.

0

2

1

Summary of Contents for PRIMERGY RX500 S7

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands