manualshive.com logo in svg

Fujitsu PRIMERGY RX500 S7, Operating Manual

Share
Download
Fujitsu PRIMERGY RX500 S7 Operating Manual Download Page 58

58

Operating Manual

 RX500 S7

Hardware installation

5.5

Notes on connecting/disconnecting cables

V

CAUTION!

Always read the documentation supplied with the device you wish to 
connect.

Never connect, or disconnect cables during a thunderstorm.

Never pull on a cable when disconnecting it. Always take hold of the 
cable by the plug.

Follow the sequence described below to connect or disconnect external 
devices to or from the server:

Be sure to wait for 10 seconds or more after shutdown before turning the 
server on.

Connecting cables

Ê

Turn off all power and equipment switches.

Ê

Disconnect all power plugs from the properly grounded power outlets.

Ê

Connect all cables to the server and peripherals.

Ê

Plug all data communication cables into the utility sockets.

Ê

Plug all power cords into the properly grounded power outlets.

Disconnecting cables

Ê

Turn off all power and equipment switches.

Ê

Disconnect all power plugs from the properly grounded power outlets.

Ê

Unplug all data communication cables from the utility sockets.

Ê

Disconnect the relevant cables from the server and all the peripherals.

I

For connecting or disconnecting LAN cables, the server does not need 
to be powered off. To avoid loss of data teaming function has to be 
enabled.

Summary of Contents for PRIMERGY RX500 S7

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands