manualshive.com logo in svg

Fujitsu PRIMERGY RX500 S7, Operating Manual

Share
Download
Fujitsu PRIMERGY RX500 S7 Operating Manual Download Page 26

26

Operating Manual

 RX500 S7

Functional overview

Slots

Drive bays

Remote Management 
Controller 

Integrated Remote Management Controller 
(iRMC S3, 32 MB attached memory incl. graphics 
controller), IPMI 2.0 compatible

Trusted Platform 
Module (TPM)

Infineon TCG V1.2 compliant (option)

PCI-Express 3.0 x8 

9 x full height (hereof 1 is reserved for Modular RAID 
controller and 1 is reserved for Modular LAN 
controller)

PCI-Express 3.0 x16 

2 x full height

Slot notes

One PCIe Gen3 x8 slot may be occupied with a 
modular LAN controller if configured. 

One PCIe Gen3 x8 slot may be occupied with a 
modular RAID controller if configured.

Important:
7 PCIe x8 slots are supported with the 1./2. 
processor. 4 additional PCIe x8 slots are supported 
only with 3./4. processor.

Hard disk bay 
configuration 

8 x 2.5-inch hot-plug SAS / SATA

Accessible drive bays 

1 x 5.25/0.5-inch for optical drives
1 x 5.25/1.6-inch for backup devices

Summary of Contents for PRIMERGY RX500 S7

























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands