Fujitsu PRIMERGY RX4770 M2 Operating Manual Download Page 80

Page: 80 / 84

Operating Manual

RX4770 M2

Troubleshooting and tips

8.3

Screen remains blank

Monitor is switched off

Switch on your monitor.

Screen has gone blank

Press any key on the keyboard.

Deactivate screen saver. Enter the appropriate password.

Brightness control is set to dark

Set the brightness control on the monitor to light. For detailed information,
refer to the operating manual supplied with your monitor.

Power cable or monitor cable not connected

Switch off the monitor and the server.

Check whether the power cable is properly connected to the monitor and to
the grounded power outlet.

Check whether the monitor cable is properly connected to the server and
monitor (if it is plugged in with a connector). If a separate graphics card is
installed in the server, then the monitor cable must be connected to the
graphics card.

Switch on the monitor and the server.

Summary of Contents for PRIMERGY RX4770 M2





















































































Search results

Summary of Contents for PRIMERGY RX4770 M2

Reviews:

Related manuals for PRIMERGY RX4770 M2

Brands by name

Popular brands

Fujitsu PRIMERGY RX4770 M2, Operating Manual

Search results

Summary of Contents for PRIMERGY RX4770 M2

Reviews:

Related manuals for PRIMERGY RX4770 M2

Brands by name

Popular brands