Fujitsu PRIMERGY RX4770 M2 Operating Manual Download Page 67

Page: 67 / 84

RX4770 M2

Operating Manual

Starting up and operation

6.1.1.4

Indicators on the hot-plug HDD/SSD/PCIe SSD modules

Figure 9: Indicators on a hot-plug HDD/SSD/PCIe SSD module

If a hard disk drive or solid state disk continuously indicates an error, the drive
should be replaced as soon as possible. This can be done during operation.

HDD/SSD BUSY (green)

– Lights up: HDD/SSD/PCIe SSD in active phase (drive active, drive

being accessed)

– Does not light: HDD/SSD/PCIe SSD inactive (drive inactive)

HDD/SSD FAULT (orange)

– Does not light: no HDD/SSD/PCIe SSD error
– Lights up: HDD/SSD/PCIe SSD Faulty or Rebuild Stopped (drive

defective/needs replacing, a rebuild process was stopped or the
HDD/SSD module is not correctly inserted)

– Slow flashing: HDD/SSD/PCIe SSD Rebuild (the data is being

restored after changing a drive)

햲

Summary of Contents for PRIMERGY RX4770 M2





















































































Search results

Summary of Contents for PRIMERGY RX4770 M2

Reviews:

Related manuals for PRIMERGY RX4770 M2

Brands by name

Popular brands

Fujitsu PRIMERGY RX4770 M2, Operating Manual

Search results

Summary of Contents for PRIMERGY RX4770 M2

Reviews:

Related manuals for PRIMERGY RX4770 M2

Brands by name

Popular brands