manualshive.com logo in svg

Fujitsu PRIMERGY RX330 S1, Operating Manual, Page: 59 / 94

Share
Download
Fujitsu PRIMERGY RX330 S1 Operating Manual Download Page 59

RX330 S1

Operating manual

59

Starting up and operation

Configuring the server

5.3.2

Configuration with ServerStart

With the 

ServerStart

 Disc 1 provided, you can configure the server and install the 

operating system in a convenient manner. Menu-guided configuration includes 
server configuration with the 

SCU

 and RAID controller configuration with 

ServerViewRAID

.

The ServerStart advantages

–

Automatic configuration of your server’s hardware and disk arrays.

–

Installation assistance for all leading server operating systems.

–

Creation of configuration files for unattended installation of several 
PRIMERGY servers with identical hardware configurations.

–

Installation of drivers and additional software.

I

The software that can be installed depends on your server’s hardware 
configuration. This configuration is detected automatically.

I

Descriptions of operating systems not covered in the RAID controller 
manual are provided in the appropriate readme files on the driver CDs.

To find out how to operate 

ServerStart

 and for further information, refer to the 

corresponding manual (see 

“Literature” on page 87

).

If you are using 

ServerStart

, you can skip the following section on how to 

configure the server and install the operating system. Continue from the 

“Cleaning the server” on page 60

 section.

Summary of Contents for PRIMERGY RX330 S1































































































Reviews:

No comments