Fujitsu MHY2040BS Page 168 Product/Maintenance Manual Download

Page: 168 / 322

Interface

Host

Reg. HD

PIO Setup

Data (1sector)

Data

(4 sectors)

Device

Data

(4 sectors)

Block

Partial

Block

Figure 5.12 Execution example of READ MULTIPLE command

•

Error reporting conditions

(1) A specified address exceeds the range where read operations are allowed

(ST = 51h, ER = 10h).

(2) The range where read operations are allowed will be exceeded by an address

during a read operation (ST = 51h, ER = 10h).

(3) An uncorrectable disk read error occurred (ST = 51h, ER = 40h).

(4) The sync byte indicating the beginning of a sector was not found

(ST = 51h, ER = 01h).

(5) The READ MULTIPLE command is disabled (ST = 51h, ER = 04h).

(6) A SATA communication error occurred (ST = 51h, ER = 0Ch).

(7) An error other than the above errors occurred (ST = 51h, ER = 04h).

5-90

C141-E269

Summary of Contents for MHY2040BS



































































































































































































































































































































Search results

Summary of Contents for MHY2040BS

Reviews:

Related manuals for MHY2040BS

Brands by name

Popular brands

Fujitsu MHY2040BS, Product/Maintenance Manual

Search results

Summary of Contents for MHY2040BS

Reviews:

Related manuals for MHY2040BS

Brands by name

Popular brands