Fujitsu MHY2040BS Page 34 Product/Maintenance Manual Download

Page: 34 / 322

Device Overview

(6) Current fluctuation (Typ.) at +5 V when power is turned on

Figure 1.3 Current fluctuation (Typ.) at +5 V when power is turned on

1.4 Environmental Specifications

Table 1.4 lists the environmental specifications.

Table 1.4 Environmental specifications

Item Specification
Temperature

• Operating

• Non-operating
• Thermal

Gradient

C to 55

C (ambient)

C to 60

C (disk enclosure surface)

–40

C to 65

C/h or less

Humidity

• Operating
• Non-operating
• Maximum Wet Bulb

8 % to 90 % RH (Non-condensing)
5 % to 95 % RH (Non-condensing)
29

C (Operating)

C (Non-operating)

Altitude (relative to sea level)

• Operating
• Non-operating

–300 to 3,000 m
–300 to 12,000 m

1-10

C141-E269

Summary of Contents for MHY2040BS



































































































































































































































































































































Search results

Summary of Contents for MHY2040BS

Reviews:

Related manuals for MHY2040BS

Brands by name

Popular brands

Fujitsu MHY2040BS, Product/Maintenance Manual

Search results

Summary of Contents for MHY2040BS

Reviews:

Related manuals for MHY2040BS

Brands by name

Popular brands