Fujitsu MHY2040BS Page 268 Product/Maintenance Manual Download | Manualshive

Page: 268 / 322

background image

Operations

6.1 Reset and Diagnosis

This section explains the device responses to power-on and an accepted reset.

6.1.1 Response to power-on

Immediately after power is turned on, the host sets 0x7Fh in the Status field of the
Shadow Block and 0xFFh in other fields. After communication with the SATA
interface is established, the host sets 0xFFh in the Status field of the Shadow
Block. The device establishes communication with the SATA interface (PHY
Ready) within 10 ms. The device sends the FIS (STS = 50h) to notify the host that
the device is ready.

Note: Figure 6.1 assumes that power is turned on after the power-off state

continued for more than five seconds.

Figure 6.1 Response to power-on (when the host is powered

on earlier than the device)

6-2

C141-E269

«
...
266
267
268
269
270
...
»

Summary of Contents for MHY2040BS



































































































































































































































































































































Reviews:

No comments

Related manuals for MHY2040BS

TotalStorage DS4800

Brand: IBM Pages: 250

TotalStorage DS4800

Brand: IBM Pages: 234

Brand: IBM Pages: 136

System Storage DS5020

Brand: IBM Pages: 31

Netfinity EXP300

Brand: IBM Pages: 93

Brand: IBM Pages: 270

Ultrastar 36LZX

Brand: IBM Pages: 2

DCAS-32160 - Ultrastar 2.1 GB Hard Drive

Brand: IBM Pages: 232

System Storage TS3310

Brand: IBM Pages: 531

Brand: WATSON Pages: 12

Brand: SanDisk Pages: 44

Brand: Schaffner Pages: 4

Brand: Glyph Pages: 2

Brand: Impediment Pages: 256

Brand: Far Tools Pages: 10

Brand: Ledger Pages: 7

PREMIER GAMT41HWJG

Brand: Gladiator Pages: 24

Brand: Panasonic Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands