manualshive.com logo in svg

Fujitsu MHY2040BS, Product/Maintenance Manual

Share
Download
Fujitsu MHY2040BS Product/Maintenance Manual Download Page 178

Interface 

 

(23)  READ BUFFER (X 'E4') 

The host system can read the current contents of the data buffer of the device by 
issuing this command. 

Upon receipt of this command, the device transfers the PIO Setup.  After that, the 
host system can read up to 512 bytes of data from the buffer. 

• 

Error reporting conditions 

(1)  A SATA communication error occurred (ST = 51h, ER = 0Ch). 

 

At command issuance (Shadow Block Registers setting contents) 

CM 

1 1 1 0 0 1 0  0 

DH 

x x x x 

xx 

CH 

CL 

SN 

SC 

FR 

xx 

xx 

xx 

xx 

xx 

 
 

At command completion (Shadow Block Registers contents to be read) 

ST Status 

information 

DH 

x x 

xx 

x x 

CH 

CL 

SN 

xx 

xx 

Error information 

SC 

ER 

xx 

xx 

 

5-100 

C141-E269 

Summary of Contents for MHY2040BS



































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands