Fujitsu MHA2021AT Product Manual Download Page 113

Page: 113 / 177

Interface

5-52

C141-E042-01EN

At command issuance (I/O registers setting contents)

1F7

(CM)

X’99’ or X’E6’

1F6

(DH)

1F5

(CH)

1F4

(CL)

1F3

(SN)

1F2

(SC)

1F1

(FR)

At command completion (I/O registers contents to be read)

1F7

(ST)

Status information

1F6

(DH)

1F5

(CH)

1F4

(CL)

1F3

(SN)

1F2

(SC)

1F1

(ER)

Error information

(26) CHECK POWER MODE (X’98’ or X’E5’)

The host checks the power mode of the device with this command.

The host system can confirm the power save mode of the device by analyzing the
contents of the Sector Count and Sector registers.

The device sets the BSY bit and sets the following register value. After that, the
device clears the BSY bit and generates an interrupt.

Power save mode

Sector Count register

• During moving to standby mode

• Standby

mode

• During returning from the standby mode

X’00’

• Idle

mode

X’FF’

• Active

mode

X’FF’

Summary of Contents for MHA2021AT


















































































































































































Search results

Summary of Contents for MHA2021AT

Reviews:

Related manuals for MHA2021AT

Brands by name

Popular brands

Fujitsu MHA2021AT, Product Manual

Search results

Summary of Contents for MHA2021AT

Reviews:

Related manuals for MHA2021AT

Brands by name

Popular brands