Fujitsu Halcyon AOU12RLQ Service Instructions Manual Download Page 31

Page: 31 / 81

Defrost Flow Chart

The defrosting shall proceed by the integrating operation time and outdoor heat exchanger

temperature as follows.

(Not defrosted for 10 minutes)

(In case of 1st defrost)

(In case of 2nd and later defrost)

Compressor OFF

Outdoor fan motor OFF

30 sec later four - way valve OFF

36 sec later compressor ON

Heating operation start : Compressor ON

Compressor integrating

operation:

Over 20 minutes to

below 60 minutes

Compressor integrating

operation:

Over 60 minutes to

below 240 minutes

Compressor integrating

operation:

Over 240 minutes

Compressor integrating

operation:

Over 35 minutes to

below 240 minutes

Compressor integrating

operation:

Over 240 minutes

Outdoor heat exchanger

temperature:

Below - 16

°F(-9°C)

Outdoor heat exchanger

temperature:

Outdoor heat exchanger

temperature:

Outdoor heat exchanger

temperature:

Outdoor heat exchanger

temperature:

Defrost start

Defrost Indicator:

[Operation lamp]

7 sec ON / 2 sec OFF

Outdoor heat exchanger temperature:

Over 50°F(10°C) / 61°F(16°C)

Compressor ON time:

Over 15 minutes

Defrost end

Below - 23

°F(-5°C)

Below - 27

°F(-3°C)

Below - 21

°F(-6°C)

Below - 27

°F(-3°C)

05-15

Summary of Contents for Halcyon AOU12RLQ


















































































Search results

Summary of Contents for Halcyon AOU12RLQ

Reviews:

Related manuals for Halcyon AOU12RLQ

Brands by name

Popular brands

Fujitsu Halcyon AOU12RLQ, Service Instructions Manual

Search results

Summary of Contents for Halcyon AOU12RLQ

Reviews:

Related manuals for Halcyon AOU12RLQ

Brands by name

Popular brands