background image

Installation Instructions

40MKCB**F/24AHA4

40MKCB**F/124ANS

40MKQB**F/25HHA4

40MKQB**F/224ANS

Under Ceiling/Floor Console Ductless Split

Sizes 18 to 54

Fig. 1 -- Indoor Unit, Outdoor Unit, and Remote Control

NOTE

:

Read the entire instruction manual before starting the

installation.

TABLE OF CONTENTS
SAFETY CONSIDERATIONS

1

PARTS LIST

2

DIMENSIONS -- INDOOR

3

DIMENSIONS -- OUTDOOR

4

CLEARANCES -- INDOOR

6

CLEARANCES -- OUTDOOR

6

SYSTEM REQUIREMENTS

6

INSTALLATION

8

INSTALL INDOOR UNIT

8

INSTALL OUTDOOR UNIT

11

ELECTRICAL DATA

15

START--UP

19

TROUBLESHOOTING

22

!

WARNING

UNIT OPERATION AND SAFETY HAZARD

Failure to follow this warning could result in personal injury or

equipment damage.
Puron refrigerant systems operate at higher pressures than

standard R--22 systems. To avoid damage to the unit or

possible personal injury, do not use R--22 service equipment or

components on Puron refrigerant equipment.

SAFETY CONSIDERATIONS

Improper installation, adjustment, alteration, service, maintenance,

or use can cause explosion, fire, electrical shock, or other
conditions which may cause death, personal injury, or property

damage. Consult a qualified installer, service agency, or your
distributor or branch for information or assistance. The qualified

installer or agency must use factory--authorized kits or accessories

when modifying this product. Refer to the individual instructions
packaged with the kits or accessories when installing.
Follow all safety codes. Wear safety glasses, protective clothing, and
work gloves. Use quenching cloth for brazing operations. Have a fire

extinguisher available. Read these instructions thoroughly and follow

all warnings or cautions included in the unit literature and on labels
attached to the unit. Consult local building codes and current editions

of the National Electrical Code ( NEC ) NFPA 70. In Canada, refer to
current editions of the Canadian electrical code CSA 22.1.

Recognize safety information. This is the safety--alert symbol

!!

When you see this symbol on the unit and in instructions or manuals,
be alert to the potential for personal injury. Understand these signal

words;

DANGER

,

WARNING

, and

CAUTION

. These words are

used with the safety--alert symbol.

DANGER

identifies the most

serious hazards which

will

result in severe personal injury or death.

WARNING

signifies hazards which

could

result in personal injury or

death.

CAUTION

is used to identify unsafe practices which

may

result in minor personal injury or product and property damage.

Summary of Contents for 40MKCB**F/24AHA4

























Reviews: