Fujitsu Fujitsu fi-5950 Operator'S Manual Download Page 236

Page: 236 / 257

216

8.24 Imprinter Selection

8.24 Imprinter Selection

You can specify which imprinter to use; Pre-imprinter or Post-imprinter, if you already have installed these
options.

Configure the settings for the Imprinter Selection as follows:

Start up the Software Operation Panel.

Refer to

“8.1 Scanner Settings” on page 173

Select [Device Setting 2] from left side list in the window, and select
[Imprinter selection] from its lower level.

Select the Imprinter to use.

Normal (obey Host specification) : Complies with the scanner driver setting.
Forcibly select Pre-imprinter

: Pre-imprinter is forcibly used to print unless directed by

the scanner driver.

Forcibly select Post-imprinter

: Post-imprinter is forcibly used to print unless directed by

the scanner driver.

HINT

For details on the specifications of the imprinter, refer to

“9 OPTIONS” on

page 223

Summary of Contents for Fujitsu fi-5950


































































































































































































































































Search results

Summary of Contents for Fujitsu fi-5950

Reviews:

Brands by name

Popular brands

Fujitsu Fujitsu fi-5950, Operator'S Manual

Search results

Summary of Contents for Fujitsu fi-5950

Reviews:

Brands by name

Popular brands