manualshive.com logo in svg

Fujitsu Fujitsu fi-5950, Operator'S Manual

Share
Download
Fujitsu Fujitsu fi-5950 Operator'S Manual Download Page 195

175

8.1 Scanner Settings

8

SCANNER SETTINGS

■

Password Setting

By setting a password, the Software Operation Panel can run in [View Only mode] which allows users to 
only view the scanner settings.
The scanner settings can be configured if no password is set.
In order to prevent unnecessary changes to the settings, a password can be used to restrict user operations.

Setting a Password

Set a password in the following procedure.

1.

Right-click the Software Operation Panel icon in the taskbar, and select 
[Password Setting] from the menu.

⇒

 The [Password setting] dialog box appears.

2.

Enter a password then again to confirm, and click the [OK] button.

Up to 32 characters can be used for the password.
Note that only alphanumeric characters (a to z, A to Z, 0 to 9) are allowed.

⇒

 A message dialog box appears.

3.

Click the [OK] button.

⇒

 The password is set.

ATTENTION

1.The user must configure password settings and perform initialization.
2.Keep the password you set written down in order not to forget it.

Summary of Contents for Fujitsu fi-5950


































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands