manualshive.com logo in svg

Fujitsu Fujitsu fi-5950, Operator'S Manual

Share
Download
Fujitsu Fujitsu fi-5950 Operator'S Manual Download Page 235

215

8.23 Jam Detection Outside of Scannable Area When Transporting paper

8

SCANNER SETTINGS

8.23 Jam Detection Outside of Scannable 

Area When Transporting paper

If this function is turned On, such a case, in which the documents are fed outside of the scannable area due 
to over-skew, is judged as a jam. You can turn it On and Off.

Configure the settings for the Jam detection outside of scannable area when transporting paper as follows:

1.

Start up the Software Operation Panel.

Refer to 

“8.1 Scanner Settings” on page 173

.

2.

Select [Device Setting 2] from left side list in the window, and select [Jam 
detection outside of scannable area when transporting paper] from its 
lower level.

3.

Select “Enable” to judge such a scan as a jam, and select “Disable” not to 
judge it as a jam.

Summary of Contents for Fujitsu fi-5950


































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands