Fujitsu AD11 Manual Download Page 53

Page: 53 / 64

3 - 17

BIOS Setup

SB I/O Base Address

This feature allows you to select the SB I/O base address, if the onboard
Legacy audio chosen. The options are: 220H, 240H, 260H, 280H.

SB IRQ Select

This feature allows you to select the SB IRQ, if the onboard Legacy audio
chosen. The options are: IRQ 5, IRQ 7, IRQ 9, IRQ 10.

SB DMA Select

This feature allows you to select the SB DMA channel, if the onboard
Legacy audio chosen.
The options are: DMA0, DMA 1, DMA 2, DMA 3.

MPU-401

This feature allows you to enable MPU-401, if the onboard Legacy audio
chosen. The options are: Disabled, Enabled.

MPU-401 I/O Address

This feature allows you to select the MPU-401 I/O address, if the onboard
Legacy audio chosen.
The options are: 300-303H, 310-313H, 320-323H, 330-333H.

Game Port (200-207H)

This feature allows you to select the game port (200-207H), if the onboard
Legacy audio chosen.
The options are: Enabled, Disabled.

Summary of Contents for AD11

































































Search results

Summary of Contents for AD11

Reviews:

Related manuals for AD11

Brands by name

Popular brands

Fujitsu AD11, Manual

Search results

Summary of Contents for AD11

Reviews:

Related manuals for AD11

Brands by name

Popular brands