Fujitsu AD11 Manual Download Page 16 | Manualshive

Page: 16 / 64

background image

2 - 6

AD11 Mainboard Manual

3).

CPU Fan Installation

2).

Front Panel Block Cable Connection

This connector is linked to the CPU fan. When the system is in suspend mode, the
CPU fan will turn off; when it reverts back to full on mode, the fan will turn back on.

Without sufficient air circulation, the CPU may overheat resulting in damage
to both the CPU and the mainboard.

Damage may occur to the mainboard and/or the CPU fan if these pins are
used incorrectly. These are not jumpers, do not place jumper caps over these
pins.

«
...
14
15
16
17
18
...
»

Summary of Contents for AD11

































































Reviews:

No comments

Related manuals for AD11

Brand: Yamaha Pages: 87

Brand: CIRCUIT DESIGN Pages: 9

Brand: Telit Wireless Solutions Pages: 5

Brand: QDI Pages: 85

NORA-W10 Series

Brand: Ublox Pages: 22

Brand: Supero Pages: 107

Brand: Acorp Pages: 74

Brand: Pentair Pages: 4

975X Platinum Series

Brand: MSI Pages: 157

Brand: Gigabyte Pages: 31

Brand: Analog Devices Pages: 8

Brand: JETWAY Pages: 57

Brand: ETOP Pages: 68

Brand: NXP Semiconductors Pages: 35

Brand: NXP Semiconductors Pages: 2

Brand: ASROCK Pages: 92

Brand: MSI Pages: 180

M3A78-CM - Motherboard - Micro ATX

Brand: Asus Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands