Fujitsu AB*G30LRTE series Service Instruction Download Page 32

Page: 32 / 71

Trouble shooting 3

INDOOR UNIT Error Method:

Detective Actuators:

Detective details:

Forecast of Cause:

Check Point 2 : Check Wired Remote Controller and Controller PCB

Check Point 1 : Check the connection of terminal

Indicate or Display:

Wired Remote Controller

Communication Error

Indoor unit Controller PCB

Wired Remote Controller (Option)

1. Connection failure 2. Wired Remote Controller failure 3. Controller PCB failure

Check & correct the followings.

Check the connection of terminal between Wired Remote Controller and indoor unit,

and check if there is a disconnection of the cable.

When the indoor unit cannot properly receive the signal from

Wired Remote Controller for 1 minute or more.

02-05

Refer to error code table.

>> If it is DC12V, Remote Control is failure. (Controller PCB is normal) >> Replace Remote Control

>> If it is DC 0V, Controller PCB is failure. (Check Remote Control once again) >> Replace Controller PCB

Check Voltage at CN14 (terminal 1-3) of Controller PCB.

(Power supply to Remote Control)

Summary of Contents for AB*G30LRTE series








































































Search results

Summary of Contents for AB*G30LRTE series

Reviews:

Related manuals for AB*G30LRTE series

Brands by name

Popular brands

Fujitsu AB*G30LRTE series, Service Instruction

Search results

Summary of Contents for AB*G30LRTE series

Reviews:

Related manuals for AB*G30LRTE series

Brands by name

Popular brands