Fujitsu Siemens Computers PRIMERGY TX150 Operating Manual Download Page 77

Page: 77 / 105

A26361-K879-Z102-3-7619

Problem Solutions and Tips

Drives ”dead“ at System Boot

7.10

Drives ”dead“ at System Boot

This error message may occur when the server has a RAID controller:

RAID controller configuration incorrect

Check and correct the settings for the drives with the RAID controller utility.

Further information is provided in the manual on the RAID controller.

7.11

Added Drive Defective

This error message may occur when the server has a RAID controller:

RAID controller is not configured for this hard disk drive

The drive was installed with the system switched OFF.

Reconfigure the RAID controller for the drive with the corresponding utility.
Information is contained in the documentation on the RAID controller.

Re-insert the HDD module with the system switched ON into a free module
bay.

If the hard disk drive continues to be shown as defective, then replace it (see
section “Installing/Removing HDD/Dummy Module” on page 77).

7.12

Error Messages on the Monitor

The meanings of the error messages are explained in the manual for

BIOS Setup

and in the documentation for the relevant components and programmes on the
PRIMERGY ServerBooks CD.

Summary of Contents for PRIMERGY TX150










































































































Search results

Summary of Contents for PRIMERGY TX150

Reviews:

Related manuals for PRIMERGY TX150

Brands by name

Popular brands

Fujitsu Siemens Computers PRIMERGY TX150, Operating Manual

Search results

Summary of Contents for PRIMERGY TX150

Reviews:

Related manuals for PRIMERGY TX150

Brands by name

Popular brands