FUJI CONTROLS IN-100 Instruction Manual Download Page 43

Page: 43 / 61

Setting

Filter

What is "Filter"?

When load value is unstable, set a low-path filter or the number of moving average to

stabilize the load value.

A low-path filter can remove instantaneous changes such as external noises and

stabilize load values.

The function of the number of moving average calculates the average of loads for the set

number to stabilize the load value.

How to set

1. Press MENU key.

2. Use



⋀



⋁

key to select

Condition Setting

3. Press SET key.

4. Use



⋀



⋁

key to select

Filter

5. Press SET key.

6. Use



key to select the appropriate low-path filter. (default: 100)

7. Press SET key and confirm the cursor has turned green.

8. Press SET key again.

9. Use



key to select the appropriate number of moving average. (default: OFF)

10. Press SET key and confirm the cursor has turned green.

11. Press SET key again to complete this operation.

Summary of Contents for IN-100






























































Search results

Summary of Contents for IN-100

Reviews:

Related manuals for IN-100

Brands by name

Popular brands

FUJI CONTROLS IN-100, Instruction Manual

Search results

Summary of Contents for IN-100

Reviews:

Related manuals for IN-100

Brands by name

Popular brands