FUHR NB649N Installation And Operation Instructions Manual Download Page 11

WWW.FUHR.DE

11

834

autotronic

881

multitronic

5.3    Tuning in the radio fi ngerprint scanner to a multitronic/autotronic control with 

radio receiver

The radio fi ngerprint scanner is tuned in to the 

multitronic

/

autotronic

 control after the user-fi nger has been 

stored. The radio fi ngerprint scanner is tuned in in exactly the same manner as a new radio key (refer to the 
 

multitronic

/

autotronic

 834 installation and operating instructions).

An abridged version of the tuning in procedure:
1. Hold the master radio key (with the red buttons) in your hand.
2.  Press the tune-in button 

(A) briefl y (for approx. 1 second)

  between the LED’s on the 

multitronic

/

autotronic

 control positioned on the inside of the building. The green LED 

(B)

 on the 

multitronic

/

autotronic

 control begins to fl ash! Ensure that the doors’ tappet contacts touch the surface-contact in the 

door frame during this procedure.  

 

Step 3 and 4 must each be carried out within 20 seconds.

3.  Now go to the outside radio fi ngerprint scanner and activate the master radios key’s (with the red buttons) 

previously tuned in button. (If the control accepts the master radio key, the 

multitronic

/

autotronic

 control’s 

green LED 

(B)

 lights up initially for 2 seconds and then continues to fl ash.)

4.  Now swipe any of the previously tuned in 

user-fi ngers

 of the desired channel 

immediately

 over the 

fi ngerprint scanner. In doing so, the radio fi ngerprint scanner’s green LED must light up briefl y. As soon as the 
LED goes out, swipe the 

same fi nger again

 over the fi ngerprint scanner. Here again, the green LED light up 

briefl y.

Analogously, the tuning in procedure applies by using the radio receiver module NBFP490.

Advice:
If you need more than 20 seconds each for both step 3 and step 4, the tuning in procedure is 
aborted and you must start again at step 1. If the tuning in procedure has been carried out 
correctly, the motor-lock door can now be opened with the tuned in channels’ user-fi ngers.

multitronic

/

autotronic

-control with radio receiver 

and visual locking display

A

  Tune-in button

B

   Green LED

C

  Red LED

D

  Master radio key

        

Radio receiver modul 
NBFP490

C

A

A

B

D

Summary of Contents for NB649N

















Reviews: