Fritsch premium PULVERISETTE 14 Operating Instructions Manual Download Page 46

Page: 46 / 48

Index

Accident prevention . . . . . . . . . . . . . . . . . . . . . . . . 7

Authorised persons . . . . . . . . . . . . . . . . . . . . . . . . 7

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Grinding chamber . . . . . . . . . . . . . . . . . . . . . . 36

Intake filter . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Electrical connection . . . . . . . . . . . . . . . . . . . . . . 21

Emergency release . . . . . . . . . . . . . . . . . . . . . . . . 15

Exclusion of liability . . . . . . . . . . . . . . . . . . . . . . . 43

Explanation of signs . . . . . . . . . . . . . . . . . . . . . . . 10

Explanation of symbols . . . . . . . . . . . . . . . . . . . . . 10

Function check . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Grinding elements

metal-free . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Removing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Grinding parts

Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Grinding process . . . . . . . . . . . . . . . . . . . . . . . . . 28

Influencing factors . . . . . . . . . . . . . . . . . . . . . 34

With external cooling . . . . . . . . . . . . . . . . . . . 30

with impact bar insert . . . . . . . . . . . . . . . . . . . 33

with metal-free grinding elements . . . . . . . . . . 31

Grinding stock

continuous feeding . . . . . . . . . . . . . . . . . . . . . 32

Guarantee terms . . . . . . . . . . . . . . . . . . . . . . . . . 41

Influencing factors

Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

sieve perforation size . . . . . . . . . . . . . . . . . . . 34

Source material feed rate . . . . . . . . . . . . . . . . . 34

Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Initial start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Materials

Feed quantity . . . . . . . . . . . . . . . . . . . . . . . . . 18

Feed size . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Operating noise level . . . . . . . . . . . . . . . . . . . . . . 17

Power consumption . . . . . . . . . . . . . . . . . . . . . . . 17

Requirements for the user . . . . . . . . . . . . . . . . . . . 7

Rotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Safety information . . . . . . . . . . . . . . . . . . . . . . . . 10

Safety logbook . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . . . 20

Setting up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Sieve ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Skilled workers . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Standstill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Stopping the device . . . . . . . . . . . . . . . . . . . . . . . 23

Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Using the device . . . . . . . . . . . . . . . . . . . . . . . . . 24

Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Warning information . . . . . . . . . . . . . . . . . . . . . . 10

WEEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Index

- 46 -

Summary of Contents for premium PULVERISETTE 14

















































Search results

Summary of Contents for premium PULVERISETTE 14

Reviews:

Fritsch premium PULVERISETTE 14, Operating Instructions Manual, Page: 46 / 48

Search results

Summary of Contents for premium PULVERISETTE 14

Reviews: