manualshive.com logo in svg

Fritsch premium PULVERISETTE 14, Operating Instructions Manual, Page: 16 / 48

Share
Download
Fritsch premium PULVERISETTE 14 Operating Instructions Manual Download Page 16

2.8  Electrical safety

2.8.1  General information

n

The main switch separates the PULVERISETTE 14 premium line from

the mains on two poles.

n

Switch off the main switch if the PULVERISETTE 14 premium line is

idle for a longer period of time (e.g. overnight).

2.8.2  Protection against restart

In case of power failure during operation or after switching off with the

main switch, the housing cover is locked. The lock of the housing cover is

opened when the power returns. For safety reasons, however, the PUL-

VERISETTE 14 premium line does not restart.

2.8.3  Overload protection

The power consumption is permanently monitored. The monitor

switches off the motor after a continuous overload. To rectify the mal-

function, switch off the PULVERISETTE 14 premium line and remove the

blockage. Afterwards, switch the device back on and start the motor by

pressing the [ START ] button.
The device switches off if the drive motor becomes too hot.
The PULVERISETTE 14 premium line switches off when the drive is

blocked ( 

Ä

 ‘Repairs’ on page 39).

 

Safety information and use

 

 

- 16 -

 

Summary of Contents for premium PULVERISETTE 14

















































Reviews:

No comments