manualshive.com logo in svg

Fritsch premium PULVERISETTE 14, Operating Instructions Manual, Page: 37 / 48

Share
Download
Fritsch premium PULVERISETTE 14 Operating Instructions Manual Download Page 37

8 

Maintenance

DANGER!
Mains voltage
– Before beginning with maintenance work, unplug the

mains plug and protect the device against being unin-

tentionally switched back on again!

– Indicate maintenance work with warning signs.
– Maintenance work may only be performed by special-

ised personnel.

– Put safety equipment back into operation after mainte-

nance or repair work

We recommend keeping a safety logbook 

Ä

 Chapter 13

‘Safety logbook’ on page 45, where all work (maintenance,

repairs......) performed on the device is entered.

The most important element of maintenance is regular

cleaning:

8.1  Intake filter

On the base of the PULVERISETTE 14 premium line, the intake area for

cool air entering the device is protected with a filter mat so that only rel-

atively dust-free cooling air is taken into the device.

NOTICE!
Maintenance of this filter mat is absolutely required. The

drive motor is not sufficiently cooled when the filter mat is

excessively soiled. This results in motor failure.

To check the filter mat, proceed as follows:

 

Maintenance

 

 

- 37 -

 

Summary of Contents for premium PULVERISETTE 14

















































Reviews:

No comments