Frigidaire FFH17F7HWC Use & Care Manual Download

Page: 9 / 44

DOOR REMOVAL INSTRUCTIONS

To remove the refrigerator doors:

1 Trace lightly around the door’s top hinges

with a pencil. This makes reinstallation

easier.

2 Disconnect the harness by grasping both

sides of the connector firmly, depress the

latch, and pull apart. Remove the two

screws from the top hinge. Lift the door

off of the bottom hinge and set it aside.

3 Detach the water tube from the connector

located behind the refrigerator and pull

the tube back out to the front of the unit.

The connector releases when you press

inward on the outer sleeve while pushing

the tube toward the connector then while

continuing to hold in the sleeve, pull the

tube away.

Getting through narrow spaces

If your refrigerator will not fit through an

entrance area, you can remove the doors.

Check first by measuring the entrance.

To prepare for removing the doors:

1 Make sure the electrical power cord is

unplugged from the wall outlet.

2 Open the freezer drawer and remove the

toe grille (see “Installation” section).

3 Remove any food from the door shelves

and close the doors.

To remove the top hinge covers:

1 Remove the two screws from each cover

over the top door hinges.

2 Lift inside edge of hinge cover and tilt

back.

Rear

Cover

Screw

Ground

Screw

Top

Hinge

Top Hinge

Cover

Hinge

Screws

Multi-wire

Cables

Leave

Hinge

With

Door

Front

Cover Screw

Water

Line

Rear

Cover

Screw

Front

Cover Screw

Top Hinge

Cover

Hinge

Screws

Two Wire

Cables

Leave

Hinge

With

Door

Top

Hinge

Ground

Screw



NOTE

DO NOT remove the ground screw from

hinge.



NOTE

Use care while pulling the water tube from

the unit to be sure that you do not kink the

tube.

Summary of Contents for FFH17F7HWC













































Search results

Summary of Contents for FFH17F7HWC

Reviews:

Related manuals for FFH17F7HWC

Brands by name

Popular brands

Frigidaire FFH17F7HWC, Use & Care Manual

Search results

Summary of Contents for FFH17F7HWC

Reviews:

Related manuals for FFH17F7HWC

Brands by name

Popular brands