background image

35

CHANGING THE FILTER

Ordering replacement filters

Order new filters by calling 877-808-4195, 

online at www.frigidaire.com/store, or through 

the dealer where you bought your refrigerator. 

You may want to consider ordering extra filters 

when you first install your refrigerator.

  Air Filter Replacement cartridge,  
  part #

PAULTRA

Air filter 

(select models)

The air filter is located under the utility bin.

Replacing your PureAdvantage

TM

 

air filter

To ensure optimal filtering of refrigerator odors, 

you should change the air filter every six months 

(the filter status light on the Touch Panel prompts 

you to replace the filter after six months).
  1  Open the air filter door.
  2  Remove the old filter and discard it.
  3  Unpack the new filter and slide it into the 

housing. The open face of the filter should 

be installed facing downward.

  4  To close the air filter door, push the top 

and bottom to lock the door closed.

  5  Press and hold the Air Filter Reset button 

on the control panel for three seconds. 

When the display changes from “Replace” 

to “Good,” the status has been reset.

  6  The Air Filter Reset will turn itself off after 

a few seconds.

Summary of Contents for FFH17F7HWC













































Reviews: