Frigidaire FFH17F7HWC Page 8 Use & Care Manual Download

Page: 8 / 44

Open

Door

Degrees

Loosen or Remove

Screw

Bottom of Door

Loosen/Remove Screw (where applicable)

To level the doors using the adjustable

lower hinge (select models)

1 Remove all food items from door bins on

door being adjusted.

2 Open doors to 90 degrees.
3 Loosen or remove screw.



NOTE

Adjustable hinge should only be used after

doors have been leveled with rollers.

Flipper

Mullion

Screw

Flipper

Mullion

Hinge

Adjusting Flipper Mullion Screw

To adjust the flipper mullion:

1 Loosen the screw located on the flipper

mullion hinge.

2 Adjust flipper mullion height. For proper

connection with the flipper mullion guide,

there should be a separation about the

thickness of a coin (0.060 inches, or

1.5 mm) between the guide and flipper

mullion.

3 Re-tighten screw.

4 Lift the door while adjusting the washer.

To raise the door, rotate washer clockwise

(when viewed from the bottom). To lower

door, rotate washer counter-clockwise

(when viewed from the bottom).

Flipper

Mullion

Guide

Thickness

of a Coin

Adjusting Flipper Mullion Height

Hinge

Washer

Raise

Door

Lower

Door

Raising/Lowering Door

INSTALLATION

Summary of Contents for FFH17F7HWC













































Search results

Summary of Contents for FFH17F7HWC

Reviews:

Related manuals for FFH17F7HWC

Brands by name

Popular brands

Frigidaire FFH17F7HWC, Use & Care Manual

Search results

Summary of Contents for FFH17F7HWC

Reviews:

Related manuals for FFH17F7HWC

Brands by name

Popular brands