Frick XLP3 Installation Operation & Maintenance Download Page 17

140.925-IOM (APR 2019) 

Page 17

XLP3 EVAPORATIVE CONDENSERS

OPERATION

•  Apply a weather-resistant lubricant or heavy grease such 

as Anti-Seize (Frick Part # 160069) to all exposed threaded 
or flanged connections and the adjustable motor base 
threaded rod.

•  Insert desiccant bags into the control panel (if supplied) to 

absorb moisture. Seal the control panel for storage.

•  Spray coat electrical component housings (if supplied) 

with a suitable protective coa ting, such as Cosmoline® 
Weathershed, and individually cover them with plastic, 
taking care to leave openings for free air circulation.

•  Inspect the protective finish on the unit. Clean and refinish 

as required. Refer to “Corrosion Protection” on page 28 for 
more details.

Motor Recommendations

Electronically Commutated (EC) Motors

XLP3 Evaporative Condenser EC motors are designed for stor-
age at ambient temperatures of -40°F to 176°F (-40°C to 80°C). 
Prolonged periods of exposure above or below these specified 
conditions could degrade components of the motor and cause 
malfunction or premature failure.

•  Care must also be taken to protect the motor from flooding 

or from harmful chemical vapors.

•  The storage area should be free from ambient vibration. 

Excessive vibration can cause damage.

•  Keep stored motor(s) dry and protected from weather.
•  Rotate the fan once per month.
•  Precautions should be taken to prevent rodents, snakes, 

birds, or other small animals from nesting inside the 
motors. In areas where they are prevalent, precautions 
must also be taken to prevent insects from gaining access 
to the interior of the motor.

 

DANGER

Rotating equipment will cause severe personal injury or 

death to persons who come in contact. Do not perform any 

service on or near the fans, motors, and drives, or inside 

the  unit  without  first  ensuring  that  the  fans  and  pump 

motors are disconnected, locked out, and tagged out.

Belt Drive Fan System

Frick standard motors are designed for storage at ambient 
temperatures of -20°F to 104°F (-28.9°C to 40°C). Prolonged 
periods of exposure above or below these specified conditions 
could degrade components of the motor and cause malfunction 
or premature failure.

•  Motors should be removed and stored inside whenever 

possible. When indoor storage is not possible the motors 
must be covered with a tarpaulin. Do not use plastic or 
plastic film. This cover should extend below the motor and 
be secured; however, it should not tightly wrap the motor. 
This will allow the captive air space to breathe, minimizing 
formation of condensation.

•  Care must also be taken to protect the motor from flooding 

or from harmful chemical vapors.

•  The storage area should be free from ambient vibration. 

Excessive vibration can cause bearing damage.

•  Precautions should be taken to prevent rodents, snakes, 

birds, or other small animals from nesting inside the 
motors. In areas where they are prevalent, precautions 
must also be taken to prevent insects from gaining access 
to the interior of the motor.

•  If not stored indoors in a controlled environment, some 

form of heating must be utilized to prevent condensation 
from accumulating in the motor. This heating should 
maintain the winding temperature at a minimum of 9°F 
(5°C) above the ambient temperature of the surrounding 
environment, keeping it from dropping below the dew 
point where condensation could form inside the motor. 
If space heaters are supplied, they should be energized. 
Request the required voltage and transformer capacity 
from your local Frick Representative. A third option is to 
use an auxiliary heat source and keep the winding warm by 
either convection or blowing warm air into the motor.

•  Rotate the motor shaft monthly to redistribute bearing 

grease.

Figure 17a — XLP3 Evaporative Condenser with  

EC Fan System

Figure 17b — XLP3 Evaporative Condenser with  

Belt Drive Fan System

Summary of Contents for XLP3



































Reviews: