FRIATEC FRIALEN Fitting Instructions Manual Download Page 4

Page: 4 / 32

Standard publications and specifications for use

For detailed and up-to-date information on FRIALEN

Safety Fittings, please

see the technical datasheets available on the Internet (www.frialen.com).

Please observe the guidelines of the DVGW standard publications, and of the
DVS, BGR 500 (VBG 50), EN 1555, EN 12201, EN 13244, UVV and
respectively national regulations.

DANGER!
The described sequence of the processes is absolutely to be adhered to.

FRIALEN

Safety Fittings

can be used with pipes made of

PE 100,

PE 80, PE 63, PE 50

according to DIN 8074/75, EN 1555-2, EN 12201-2,

EN 13244-2, ISO 4437 and ISO 4427.
For PE pipes, a fusion flow rate MFR 190/5 in the range of 0.2 – 1.7g/10 min.
applies.

We recommend using pipes with a limited dimension tolerance range,
tolerance class B.

FRIALEN

Safety Fittings

consist of PE 100 and meet the requirements

according to DIN 16963-5, -7, EN 1555-3, EN 12201-3, EN 13244-3,
ISO 8085-3 as well as the DVGW test bases. FRIALEN

Safety Fittings can

be fused with FRIAMAT

Electrofusion Units at ambient temperatures

between - 10

C and + 45

C. Fittings from d 710 between 0

C and + 45

For material transition joints, the material- or system-specific standards and
installation guidelines apply in addition.

WARNING!
Fusion with other pipe materials such as e.g. PP, PVC etc. is not
possible.

WARNING!

Pipes and moulded components should have settled to a balanced
temperature level between - 10

C and + 45

C (Couplers UB d 710 between

C and + 45

C) when being processed.

FL_2104_8_GB_II_08.p65

25.03.2008, 9:48 Uhr

Summary of Contents for FRIALEN

































Search results

Summary of Contents for FRIALEN

Reviews:

Related manuals for FRIALEN

Brands by name

Popular brands

FRIATEC FRIALEN, Fitting Instructions Manual

Search results

Summary of Contents for FRIALEN

Reviews:

Related manuals for FRIALEN

Brands by name

Popular brands