manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Operator'S Manual

Share
Download
Fresenius Medical Care DIASAFE 2008 K Operator'S Manual Download Page 45

Chapter 2—Daily Preparation for Treatment 

2008K Hemodialysis Machine Operator’s Manual Rev P 

45 

4.

 

Verify that the concentrate type, displayed near the top of the screen, correctly matches 
the prescribed concentrate type, and that the acid/bicarbonate or acetate concentrates 
connected to the machine match the type selected.  If an incorrect concentrate type is 
displayed, the correct concentrate must be entered.  To change the concentrate selection, 
see “Setting an Acid/Bicarbonate Type” on page 66.   

 

 

Figure 20 – The Dialysate Screen 

 

Note

: If the machine is set up for use with Citrasate®, a ‘Citrate’ meter box will be 

displayed in the dialysate constituent list (Functional board software version 3.36 or later). 

5.

 

After the concentrate displayed is correct, verify that the Base Na+ and Bicarbonate are 
as prescribed.  Press the 

CONFIRM

 key, and then touch the 

Home

 screen-button.  

6.

 

Insert the bicarbonate concentrate (blue) connector into a central bicarbonate supply or a 
jug containing sufficient bicarbonate concentrate for an entire treatment.  Again, be sure 
the jug contains enough concentrate for the entire treatment 

Preparing the Extracorporeal Blood Circuit  

Use Figure 21 or Figure 22, depending on the configuration of your machine, as a guide for 
connecting the bloodlines. The red lines on the machine are guides for arterial bloodline 
(from patient to dialyzer).  The blue lines on the machine are guides for the venous bloodline 
(from the dialyzer to the patient).  Be sure to use aseptic technique for all bloodline 
connections. 

Current acid 
concentrate 
selection 

Summary of Contents for DIASAFE 2008 K

















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands