manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Operator'S Manual

Share
Download
Fresenius Medical Care DIASAFE 2008 K Operator'S Manual Download Page 164

164 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Chapter 6—Alarms and Troubleshooting 

Fail * Ven High Soft 

Fail * Ven Low Soft 

Fail * Ven High Hard 

Fail * Ven Low Hard  

Venous Pressure test has failed. 

Test 

Message 

Rerun test, if failure repeats, remove machine from service and alert 
a qualified service technician. 

** Failed Sending Data to 
Actuator Board ** 

Functional to Actuator board 
communication problem during 
startup. 

Alarm 

Turn machine power off and back on. If alarm is not cleared, take the 
machine out of service and alert a qualified service technician. 

Fill for Diasafe Test 

This message indicates the status of 
the Diasafe test 

Advisory 

Advisory only. No action is required. 

Fill Program Alarm 

A Fill program has occurred for one 
minute while blood is sensed. 

Alarm 

Inspect for air in the system.  

Correct as required. 

If the warning is not cleared, return the blood to the patient if alarm 
occurs during treatment. Take the machine out of service and alert a 
qualified service technician.

 

Filling Program 

A Fill program is in progress. 

Advisory 

Advisory only. No action is required. 

Flow Error 

General Flow Alarm 

Warning 

A single occurrence is not a problem if the machine automatically 
resets.  If the problem persists for longer than one minute or occurs 
repeatedly: 

1)  Check the water supply flow to the machine. 

2)  Check that the Dialysate Flow is on. 

3)  Check the dialyzer supply and return lines for kinks. 

4)  Set Dialysate Flow in the “Home” screen to 500 ml/min and verify 

that the flow from the drain line is 500 ml/min 

 50 ml/min. 

5)  Turn the power off and on.  If warning is not cleared, return the 

blood to the patient if alarm occurs during treatment.  

6)  Take the machine out of service and alert a qualified service 

technician. 

 
 

Summary of Contents for DIASAFE 2008 K

















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands