manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Operator'S Manual

Share
Download
Fresenius Medical Care DIASAFE 2008 K Operator'S Manual Download Page 181

Chapter 6—Alarms and Troubleshooting 

181 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Message 

Purpose of Message 

Type 

Action Required

 

Temp Sensors 
unmatched 

When the temperature trim function 
needs to change DAC by > 1

 C, the 

pre and post sensors are verified 
against one another.  This message 
occurs if the two temperature sensors 
are more than 0.5

 C different. 

Warning 

Press 

RESET

 key to reset alarm  

The temperature trim function will be disabled until the machine is 
turned off and back on. 

Temp Control not 
calibrated 

This message is displayed on the sign 
on screen if the temperature sensors 
were not matched when they were 
verified against one another. 

Advisory 

Calibrate the temperature control. 

Temperature greater than 
max. value 

Entered Temperature value is higher 
than allowed. 

Dialog 

Message 

The temperature will be set to the highest allowed level.  Press 

CONFIRM

 to clear message and accept the maximum allowed value. 

Verify that the value is acceptable. 

Temperature has been 
set to min. 

The operator has attempted to set a 
Temperature lower than allowed. 

Dialog 

Message 

The temperature will be set to the lowest allowed level. 

Test Complete 

All selected self-tests passed. 

Advisory 

Advisory only.  No action required. 

Test Failed 

The Alarm and/or PHT Sections of the 
automated Test Sequence have failed 

Test 

Alarm 

Reset the alarm.  Check the setup to see if the alarm can be 
corrected and then retest.  If the machine fails, turn machine power 
Off and back On. If alarm is still not cleared, take the machine out of 
service and alert a qualified service technician. 

Testing temp sensor 

In rare cases, the machine may be 
put into bypass to verify the 
temperature sensor.  The OLC test 
cannot be run at this time 

Advisory 

Wait 10 minutes and start the OLC test again. 

TMP is High (toward 500)  The TMP has exceeded the TMP high 

alarm limit value. 

Blood 
Alarm 

1)  Check the dialyzer supply and return lines for kinks and that the 

connectors are properly connected to the dialyzer or the shunt. 

2)  Clean the dialysate line filter screen. 
3)  Press 

RESET

 key to reset alarm. Press the 

Override

 key and 

hold for one second to select new alarm limits or for adjusting the 
TMP.  If unable to reset the alarm, call your local qualified service 
technician. 

High UF Goal and low dialyzer KUF coefficient can exceed the 
maximum TMP of 520 mmHg.  The UF Goal may need to be lowered. 
This in turn will lower the UF rate and the TMP. Notify a physician if 
the UF Goal has changed. 

 

Warning!

  A rising TMP 

may indicate a leak in the 
balancing system and 
should be investigated. 

Summary of Contents for DIASAFE 2008 K

















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands