manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Operator'S Manual

Share
Download
Fresenius Medical Care DIASAFE 2008 K Operator'S Manual Download Page 169

Chapter 6—Alarms and Troubleshooting 

169 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Message 

Purpose of Message 

Type 

Action Required

 

Less than minimum value  Entered parameter is smaller than 

allowed 

Dialog 

Message 

Verify that the minimum value is acceptable.  Press 

CONFIRM

 to 

clear message and accept the minimum allowed value. 

Lost Battery RAM Data 

The battery RAM memory has been 
lost. 

Opening 

Screen 

Message 

Verify all treatment settings before using the machine. 

Low Acetate Warning 

20% of concentrate left in acetate jug 
per entered value. 

Warning 

Check jug level, change to new jug of concentrate if needed and 
reenter jug volume. 

Low Acid Warning 

20% of concentrate left in acid jug per 
entered value. 

Warning 

Check jug level, change to new jug of concentrate if needed and 
reenter jug volume. 

Low Acid/Bicarb Warn 

20% of concentrate left in acid and 
bicarbonate jug per entered value. 

Warning 

Check jug level, change to new jug of concentrate if needed and 
reenter jug volume. 

Low Bicarb Warning 

20% of concentrate left in bicarbonate 
jug per entered value. 

Warning 

Check jug level, change to new jug of concentrate if needed and 
reenter jug volume. 

Low Flow Error 

Possible balancing chamber problem. 

Warning 

A single occurrence is not a problem if the machine automatically 
resets.  If the problem persists for longer than one minute or occurs 
repeatedly:  

1)  Check the water supply flow to the machine. 

2)  Check that the Dialysate Flow is on. 

3)  Set Dialysate Flow in the “Home” screen to 500 ml/min and verify 

that the flow from the drain line is 500 ml/min 

 50 ml/min. 

4)  Turn the power off and on.  If warning does not clear, return the 

blood to the patient if alarm occurs during treatment.  

5)  Take the machine out of service and alert a qualified service 

technician. 

 

 

 

 

Summary of Contents for DIASAFE 2008 K

















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands