manualshive.com logo in svg

Fresenius Medical Care DIASAFE 2008 K, Operator'S Manual

Share
Download
Fresenius Medical Care DIASAFE 2008 K Operator'S Manual Download Page 153

Chapter 6—Alarms and Troubleshooting 

153 

2008K Hemodialysis Machine Operator’s Manual Rev P 

Message 

Purpose of Message 

Type 

Action Required 

Blood Sensed 

An action has been initiated that 
requires that blood not be sensed.  

Warning 

1)  Inspect the optical detector below the line clamp. 

2)  Press 

RESET

 to reset the alarm. 

3)  If the alarm is not cleared, return the blood to the patient if alarm 

occurs during treatment. Take the machine out of service and 
alert a qualified service technician. 

Blood Still Sensed 

Blood is sensed by the optical 
detector while in the opening screen 
and with the red wand is put in the 
port on the front of the machine.  

Warning 

1)  Verify that there is no longer blood in the venous return line 

2)  Inspect the optical detector below the line clamp. 

3)  Reset the alarm. 

4)  If the alarm is not cleared, take the machine out of service and 

alert a qualified service technician. 

BP Comm. Timeout 

Time out when receiving Intel-Hex-
line or overflowed received buffer 

Alarm 

See message A.27 

BP Del. Rate Alarm 

Actual speed-read back analog 
voltage at X348/10 is out of limits 

Alarm 

See message A.21 

BP Direction Alarm 

Pump is turning in the wrong direction 

Alarm 

See message A.13 

BP Feedback Alarm 

Arterial rate and the blood pump’s 
arterial setting knob do not track in 
sync.  

Alarm 

If the warning is not cleared, return the blood to the patient if alarm 
occurs during treatment. Take the machine out of service and alert a 
qualified service technician.  

BP Level Up Alarm 

Pressure increase when the Level Up 
key is pressed 

Alarm 

See message A.25 

BP Pressure Alarm 

Arterial pressure-read back analog 
voltage at X348/7 is out of limits 

SN pressure-read back analog 
voltage is out of limits 

Alarm 

See message A.22 

BP Receive Alarm 

Error in received Intel-Hex-line 

Alarm 

See message A.28 

BP Rotation Error 

Pump rotor turning when it should not 
be for a second time 

Alarm 

See message E.23 

BP Set Rate Alarm 

Set speed-read back analog voltage 
at X348/14 is out of limits 

Alarm 

See message A.20 

 

Summary of Contents for DIASAFE 2008 K

















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands