background image

1

ELECTRICAL SAFETY

C A U T I O N

 Make sure all ELECTRICAL POWER IS 

OFF before connecting any electrical wires.

W A R N I N G

 Capacitor voltage may be hazardous. 

To discharge motor capacitor, hold insulated handle 
screwdriver BY THE HANDLE and short capacitor 
terminals together. Do not touch metal screwdriver blade 
or capacitor terminals or electrical shock could occur. If 
in doubt, consult a qualifi ed electrician.

Wire motor for correct 
voltage.  See “Electrical 

Installation” section of this 
manual and motor nameplate.

Ground motor 
before connecting  to             

power supply.

Meet National Electrical 
Code (NEC) or Canadian 

Electrical Code(CEC) and 
local codes for all wiring.

Follow all pump wiring 
instructions provided in 

this manual.

C A U T I O N

 

DO NOT touch an operating motor.

 The 

surface of the motor may be HOT. Allow the motor to 
cool for thirty (30) minutes before handling.

GENERAL SAFETY

•  Do not allow pump or any system component to 

freeze. To do so will void the warranty.

•  This pump has been evaluated for pumping 

water only. Pumping liquids other than water may             
void warranty.

•  Periodically inspect pump and system components.

Hazardous voltage.
Can shock, burn, or
cause death.

Ground pump before
connecting to power
supply. Disconnect
power before working
on pump, motor 
or tank.

W A R N I N G

INTRODUCTION

You have purchased one of the most user friendly 
pumps available. The Turf Boss pumps are made with 
high quality materials which are designed to provide 
you with years of reliable service. Lawn sprinklers are 
designed to maximize output fl ow, while still maintaining 
the ability to draw water from a source up to 25 feet 
below the pump.  All mechanical parts, motor, impeller, 
electrical controls, etc., are above ground within easy 
reach. If service is ever necessary, simple hand tools will 
do the job. This lawn sprinkler pump installs easily and 
quickly without the need for special tools or pump rigs. 
You can install it yourself provided you follow closely the 
instructions contained in this manual.

INSPECT YOUR SHIPMENT

All Turf Boss lawn sprinkler pumps are carefully tested, 
inspected, and packaged to insure their arrival in perfect 
condition. When the pump is received, examine it closely 
to make sure there is no damage or broken parts that 
may have occurred in shipping. If damage is evident, 
report this immediately to your shipping carrier and 
dealer. This shipping carrier assumes full responsibility 
for the shipment’s safe arrival. Any claim for damage to 
the shipment, either visible or concealed, must be made 
through the shipping carrier fi rst.

Summary of Contents for TurfBOSS TB15CI













































Reviews: