FP centormail Operator'S Manual Download Page 157

Page: 157 / 212

Troubleshooting

157

…

with envelope sealing

Envelopes are not properly
sealed

Sponge is too dry.
Pump sealing liquid into the moistening unit:
M

ENU

EALING

TART

UMP

(see also Chapter 14.21,

page 120)

Sponge is dirty or worn.
Clean or replace the sponge

(see Chapter 15.9, page 147)

You have used improper envelopes.
Only use envelopes that are suited for sealing by
machine. Observe specifications

(see page 197)

The envelope flaps are not properly moistened.
Adjust the moistening level

(see Chapter 14.21, page 120)

Envelopes are not sealed

Sealing is disabled.
Turn the envelope sealing switch to the position

SEAL.

centormail warns you
about an empty sealant
tank, although there is still
enough sealing liquid in
the tank

Tap water might produce air bubbles (depending on
the water quality of your local water supply), which
may interfere with correct filling level detection.

On the sealer: Open the lid. Pull out the yellow plug.

(See also page 145.)

The filling level sensor is located front-right of the inner
side of the tank. Using a finger, wipe over the sensor
several times.

Close the sealant tank. Close the lid.

(See also page 146.)

If problem persists: Use FP sealing liquid or distilled
water.

Problem

Possible cause and remedy

Summary of Contents for centormail





















































































































































































































Search results

Summary of Contents for centormail

Reviews:

Related manuals for centormail

Brands by name

Popular brands

FP centormail, Operator'S Manual

Search results

Summary of Contents for centormail

Reviews:

Related manuals for centormail

Brands by name

Popular brands