FP centormail Operator'S Manual Download Page 155

Page: 155 / 212

Troubleshooting

155

…

during TELESET

Cannot access TELESET
functions

From the current account, loading postage is not
permitted.

Desired amount cannot be
loaded

Amount not permissible.
Enter a different amount and try again.

TELESET procedure
aborts

centormail cannot establish a connection to the
Teleset Data Center (TDC).

Check the modem parameters

(see Chapter 14.8, page 103)

Check the TDC’s phone number

(see Chapter 14.9,

page 105)

…

during initial setup, maintenance and care

centormail fails to
recognize the ink
cartridges / print heads or
the ink tank

The ink cartridges / print heads / the ink tank were not
inserted properly.
Remove and re-insert the cartridges / print heads /
ink tank.

Wrong ink cartridges / print heads / ink tank inserted.
Please heed the specifications

(see page 195)

Ink cartridges / print heads / ink tank defective.
Call your FP servicing dealer.

Software problem.
Switch off centormail. Wait for at least 1 minute, then
switch centormail back on.

Cleaning the print system
fails to improve the print
quality

The ink cartridges / print heads are either heavily
soiled or dried out. Repeat the cleaning process: Use
the function “Intensive Clean of Print System”

(see

page 140)

If this fails to correct the error:
Manually clean the ink cartridges / print heads

(see page 141)

Problem

Possible cause and remedy

Summary of Contents for centormail





















































































































































































































Search results

Summary of Contents for centormail

Reviews:

Brands by name

Popular brands

FP centormail, Operator'S Manual

Search results

Summary of Contents for centormail

Reviews:

Brands by name

Popular brands