manualshive.com logo in svg

FOURAUDIO HD2, Manual, Page: 9 / 25

Share
Download
FOURAUDIO HD2 Manual Download Page 9

described in section 3.1.1 and 3.1.2 below.

3.1.1 Resetting To The Default IP Address (192.168.1.15)

Power on the HD2 and wait until the HD2 has finished booting. Then, use the Page keys on the front 
panel and enter the Menu 'Reset IP'. Push the knob. You get a message 'IP reset to 192.168.1.15). 
Restart the HD2.

3.1.2 Setting A Specified IP Address

Start the HD2Control software (described below). Connect to the HD2 (at 192.168.1.15). When 
connected, enter the desired IP address in the IP address field on the top left and click 

Set IP

.

Restart the HD2.

3.1.3 Network troubleshooting

In case that network operation is not working, this checklist may be helpful:

Assuming that the HD2 has an IP address of 192.168.1.15:

–

Try to access the HD2 by opening a console, typing 'ping 192.168.1.15' and see, if it reacts.

–

The console can be found under Start 

 Programs 

 Accessories.

→

→

If you get no response:

Did you use the right cable?

–

crossover cable if directly connected to PC

–

standard patch cable if connected to router/switch/hub.

Firewall active?

–

configure it to not block port 5000

Windows network settings OK?

–

TCP/IP protocol installed?

–

This is true, if internet access works

If direct connection is selected:

–

try to access a second PC

–

connect to a second PC via crossover ethernet cable

–

look up the IP address of the second PC by typing 'ipconfig' in console on that PC (look for IPv4 
address)

–

Enter 'ping <ip address of second PC>

–

If that succeeds, TCP/IP works in principle.

If the above advices aren't successful, ask an experienced network administrator with nerves of steel.

9

Summary of Contents for HD2


























Reviews:

No comments