manualshive.com logo in svg

Four Winds V475, Owner'S Manual

Share
Download
Four Winds V475 Owner'S Manual Download Page 91

Owner’s Manual Page 89

Fuel Systems - Section I 

D.  Fuel Pick-Up

The fuel withdrawal line attaches to the fuel tank at the 

fuel pick-up. See Figure I4 for fuel pick-up location.

The fuel withdrawal is positioned in the fuel 

tank to achieve optimum fuel usage, and fuel 

line routing. At certain speeds and hull trim 

angles, the fuel supply at the withdrawal can 

increase or decrease accordingly. Be extremely 

care ful when attempting to operate the boat on 

a mini mum amount of fuel. Though some fuel 

may be in the tank, the rela tive trim angle of the 

boat may cause the fuel to flow away from the 

withdrawal.

NOTICE

On the V475 models, access to the fuel fittings 

is through the engine compartment.

Figure I4:  Starboard Fuel Tank Fittings Shown

(Port & Stbd Typical)

E.  Fuel Level 

The amount of fuel in the fuel tanks can be accessed 

through the Electronic Vessel Control (EVC) system. 

An EVC display for each engine is mounted at the 

helm and monitors their respective systems to include 

fuel level. Refer to the manufacturer’s literature 

included in your owner’s packet for specific informa-

tion regarding ECV operation and information display.

F.  Fuel Senders

The fuel sender consists of a float which travels up 

and down a stationary tube. The float measures the 

level of the fuel in the tank and sends a signal to the 

EVC display. See Figure I5.

 

 

Figure I5:  Fuel Sender Operation

Due to the mechanical nature of the fuel sender, varia-

tions in readings during various speeds of operation 

may occur. This system is merely a relative indication 

of the avail able fuel supply and not a calibrated 

instru ment. With this type of sending unit a more  

accurate measurement of fuel level is obtained with 

the boat in a level position.

The display readings will also vary with the trim angle 

of the boat. When sitting at a dock and the boat is 

nearly level, the fuel display will register accurately. 

Refer to Figure I3. When boating, the trim angle of the 

boat changes and affects the gauge readings. Under 

these conditions, the fuel sender will register “full” for 

the first few hours of running time until the fuel level 

drops below the 3/4 or 1/2 mark. This is caused by the 

angle of the fuel in the tank as shown in Figure I6. 

Figure I6:  Effects of Trim Angle

Fuel Vent Hose

Diesel Return Tube

Fuel Fill Hose

Fuel Pick-Up

Fuel Sender

Summary of Contents for V475






























































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands