manualshive.com logo in svg

Fortress Technologies S1, Manual

Share
Download
Fortress Technologies S1 Manual Download Page 49

44

Then, set the siren into programming mode. The steps for 

doing that depend on which type of siren you’re adding. 

See the following pages for instructions on setting your si-

ren into programming mode. 

Once the siren is in programming mode, press the central 

button on the main panel to send a signal to the siren. The 

siren should chirp in response.

To finish programming the siren, unplug it and/or turn it 

off for at least 10 seconds.

Your siren is now programmed. You can plug in the siren 

anywhere within range of the main panel, and test it when 

you’re ready by triggering the alarm to confirm the siren 

will sound.

Setting Wireless Sirens into Programming Mode

Each of the wireless sirens compatible with the S1 GSM 

WiFi system can be set into “programming mode” as part 

of the process to add it to your system. Here are the details 

for each type of wireless siren that we offer now.

(see next pages)

Summary of Contents for S1
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands