manualshive.com logo in svg

Fortress Technologies S1, Manual

Share
Download
Fortress Technologies S1 Manual Download Page 47

42

Programming the Keypad to the Main Panel

The main panel considers the RFID Keypad to be the same 

as a Remote Key Fob, so when programming the Keypad 

to the Main Panel, it will be added the same way as Re-

mote Key Fobs.

Using the RFID Keypad

Press any key to wake up the RFID Keypad.

To send an Arm command to the main panel:

[4-Digit User Password], then the Arm button (either the 

Lock icon for Away, or the House icon for Home).

To send a Disarm command to the main panel:

[4-Digit User Password], then the Disarm button

(or swipe an RFID Key Tag in front of the Keypad.)

1.  Press and hold the Set button until the panel says,           

“Please trigger remote control,” and the light begins 

to flash red. At this point, release the Set button.

2.  To trigger the Keypad, enter the Keypad’s Current 

6-Digit Admin Password, then press the SOS button. 

The panel will say, “Remote control added successful-

ly.”

3.  Press and release the Power button once to exit listen-

ing mode.

Summary of Contents for S1
































































Reviews:

No comments

Brands by name

Popular brands

Load more brands