25
Safety devices:
- A special safety clutch that makes the machine
movements and work tool operation possible by
means of a non-release lever positioned on the
handlebars (7 Fig.1). When this lever is released,
all the machine functions stop without turning the
engine off.
- The clutch control lever has a special automatic
locking system which prevents accidental engage
-
ment of the clutch (two actions are necessary for
engaging the clutch: release using the button (15
Fig. 1) and actuation of the lever (7 Fig. 1).
Handlebars:
adjustable in height and laterally.
Reversible of 180°.
Wheels:
4.00x8 - 4.00x10 - 16x6.50x8
Wheel inflation pressure: 2.2 bar.
Dimensions:
See figure 2.
Speed:
The speed values have been calculated with
a 3600 rpm engine.
WHEELS
CUTTER Forward km/h
1
a
2
a
3
a
3,50 x 6
1,05
2,70
5,60
4,00 x 8
1,30
3,32
6,85
4,00 x10
1,46
3,73
7,68
16 x 6,5 x 8
1,30
3,32
6,85
WHEELS
CUTTER Reverse km/h
1
a
2
a
3
a
3,50 x 6
0,87
2,27
4,56
4,00 x 8
1,07
2,71
5,6
4,00 x10
1,20
3,04
6,28
16 x 6,5 x 8
1,07
2,71
5,6
N.B: In version cutter speeds are reversed.
Supplies:
Refer to the engine booklet for the type of
fuel and check the identification data on the plate on
the engine itself.
The fuel tank is part of the engine.
SECTION 2
Safety and prevention
2.1 SAFETY
The personnel shall be instructed on the risks result
-
ing from accidents on the devices arranged for the
operator’s safety and on the general accident preven
-
tion regulations provided for by the legislation of the
Country where the machine is being used.
While designing the machine, all the potential danger
-
ous situations were foreseen and consequently the
proper protections were adopted. Anyhow, the level
of accidents caused by the careless and improper use
of the machine is still high.
The carelessness, the irresponsibility and the too
much familiarity are too often the cause of accidents
as well as tiredness and sleepiness.
You shall read this manual very carefully and in partic
-
ular the section concerning the safety regulations.
DANGER
The Manufacturer shall not be held responsible for
the non-compliance with the safety and accident
prevention regulations provided for by the laws
and for the non-compliance with what is provided
for in this manual.
DANGER
Pay attention to this symbol in the instructions
manual.
It shows a possible hazard.
2.1.1 WORDS USED
Words of people and of specific situations that may
involve directly the machine an/or the persons in con
-
tact with the machine itself are here below listed.
• USER: The user is the person, the body or the com
-
pany who has purchased or rented the machine and
who intends to use it for the designed purposes.
He shall be responsible for the machine and for the
training of all those working with it.
• DANGEROUS AREA: Any area within and/or near the
machine where the presence of an exposed person
implies a hazard for the safety and the health of the
same.
• EXPOSED PERSON: Any person who is completely
or in part near a dangerous area.
• OPERATOR: A person who is able to operate, to
carry out the maintenance, to clean and to transport
the machine.
• AUTHORIZED SERVICE CENTER: The authorized
service center is the structure legally authorized
by the Manufacturer that has skilled personnel able
to perform all the service, maintenance and repair
ENGLISH
Summary of Contents for 280 Series
Page 2: ...2 Fig 1 A B C 1 A 9 10 7 8 2 3 4 6 14 12 13 11 5 10 9 16 17 16 B C 16 15 ...
Page 3: ...3 Fig 2 1 Fig 5 3 2 Fig 3 Fig 6 1 2 1 2 3 Fig 4 4 400 650 1050 1380 1700 4 1 2 3 0 5 2 mm 5 ...
Page 4: ...4 Fig 7 Fig 9 1 2 3 4 5 6 Fig 8 7 A B ...
Page 5: ...5 IT USO E MANUTENZIONE 6 EN USE AND MAINTENANCE 21 Fig 10 7 5 6 2 1 3 4 9 3 F 1 F 2 8 ...
