Ford 2010 Milan Hybrid Page 62 Owner'S Manual Download

Page: 62 / 326

Replacing exterior bulbs

Check the operation of all the bulbs frequently.

Replacing headlamp bulbs (2.5L/3.0L engines)

High beam/low beam bulb replacement

For driver side replacement of this bulb, do the following:

WARNING:

To reduce the risk of vehicle damage and/or

personal burn injuries do not start your engine with the air

cleaner removed and do not remove it while the engine is running.

1. Release the clamps that secure the air filter housing cover. See

Changing the air filter element

in the

Maintenance & Specifications

section for more information.

2. Carefully separate the two halves of the air filter housing.

3. Locate the mass air flow sensor electrical connector on the air outlet
tube. This connector will need to be unplugged.

4. Remove the air filter assembly.

5. Remove the rubber headlamp bulb access cover.

6. Remove the bulb socket by
rotating it counterclockwise, then
pull it straight out of the lamp
assembly.

7. Disconnect the electrical connector.

To install, reverse the removal procedure.

For passenger side replacement of this bulb, do the following:

1. Make sure headlamp control is in the off position, then open the hood.

2010 Milan

(mln)

Owners Guide, 1st Printing
USA

(fus)

Lights

Summary of Contents for 2010 Milan Hybrid







































































































































































































































































































































Search results

Summary of Contents for 2010 Milan Hybrid

Reviews:

Related manuals for 2010 Milan Hybrid

Brands by name

Popular brands

Ford 2010 Milan Hybrid, Owner'S Manual

Search results

Summary of Contents for 2010 Milan Hybrid

Reviews:

Related manuals for 2010 Milan Hybrid

Brands by name

Popular brands