manualshive.com logo in svg

Ford 2010 Milan Hybrid, Owner'S Manual

The Ford 2010 Milan Hybrid is an innovative and eco-friendly sedan that combines the power of a gasoline engine with the efficiency of electric motors. Enhance your driving experience with our Quick Reference Manual, available for free download at manualshive.com, providing essential information to maximize your vehicle's performance.

Share
Download
background image

passenger seat or an unbuckled child or small person in the passenger
seat. The air curtain was designed to inflate between the side window
area and occupant to further enhance the protection provided to
occupants in side impact collisions. The seat-mounted side airbag was
designed to inflate between the door panel and occupant to further
enhance the protection provided occupants in side impact collisions.

The side air curtain system SRS is designed to activate when the vehicle
sustains lateral deceleration sufficient to cause the sensors to close an
electrical circuit that initiates air curtain and seat-mounted side airbag
inflation.

The fact that the side air curtain and seat-mounted side airbag did not
inflate in a collision does not mean that something is wrong with the
system. Rather, it means the forces were not of the type sufficient to
cause activation. The side air curtain system is designed to inflate in side
impact collisions, not roll-over, rear impact, frontal or near-frontal
collisions, unless the collision causes sufficient lateral deceleration.

WARNING:

Several air bag system components get hot after

inflation. Do not touch them after inflation.

WARNING:

If the side air

curtain has deployed,

the

air curtain will not function
again. The side air curtain
system (including the A, B and
C pillar trim and headliner)
must be inspected and serviced
by an authorized dealer.

If the

air curtain is not replaced, the
unrepaired area will increase the
risk of injury in a collision.

Determining if the system is operational

The SRS uses a readiness light in the instrument cluster or a tone to
indicate the condition of the system. Refer to the

Airbag readiness

section in the

Instrument Cluster

chapter. Routine maintenance of the

airbag is not required.

2010 Milan

(mln)

Owners Guide, 1st Printing
USA

(fus)

Seating and Safety Restraints

147

Summary of Contents for 2010 Milan Hybrid







































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan Hybrid

ZAPTEC Go Instruction Manual preview
Go
Brand: ZAPTEC Pages: 240
Acdeos AXS FL Installation Instruction preview
AXS FL
Brand: Acdeos Pages: 7
Acdeos AXS FL Manual preview
AXS FL
Brand: Acdeos Pages: 38
VEAP SHIELD UNITED FT Series Mounting Instruction preview
FT Series
Brand: VEAP SHIELD UNITED Pages: 3
Jeep Commander Overview Manual preview
Commander
Brand: Jeep Pages: 25
Jeep Commander Warranty Information Booklet preview
Commander
Brand: Jeep Pages: 51
Farenheit CCD-5XS Owner'S Manual preview
CCD-5XS
Brand: Farenheit Pages: 8
KRAFTWERK Automotive 31006 Instructions preview
Automotive 31006
Brand: KRAFTWERK Pages: 2
Kia Picanto Manual preview
Picanto
Brand: Kia Pages: 680
Cadillac Fleetwood Brougham Sedan 1966 Owner'S Manual preview
Fleetwood Brougham Sedan 1966
Brand: Cadillac Pages: 56
Vauxhall 2013 Ampera Infotainment Manual preview
2013 Ampera
Brand: Vauxhall Pages: 95
Whispbar K730W Fitting Instructions Manual preview
K730W
Brand: Whispbar Pages: 14
PEUGEOT 5008 2017 Handbook preview
5008 2017
Brand: PEUGEOT Pages: 404
WABCO 2S/2M Installation Instructions Manual preview
2S/2M
Brand: WABCO Pages: 40
Gator ARV50T User Manual preview
ARV50T
Brand: Gator Pages: 18
Dodge 2009 RAM TRUCK Owner'S Manual preview
2009 RAM TRUCK
Brand: Dodge Pages: 543
SAN HIMA SH-TENT-GRAY-AHT125 User Manual preview
SH-TENT-GRAY-AHT125
Brand: SAN HIMA Pages: 11
Cadillac 2006 Escalade EXT Owner'S Manual preview
2006 Escalade EXT
Brand: Cadillac Pages: 484

Brands by name

Popular brands

Load more brands