Ford 2010 Milan Hybrid Owner'S Manual Download Page 239

Page: 239 / 326

If the battery has been disconnected and reconnected, refer to the

Battery

section of the

Maintenance and Specifications

chapter.

The high-current fuses are coded as follows.

Fuse/Relay

Location

Fuse Amp

Rating

Protected Circuits

50A*

Electronic power assist steering
B+

50A*

Electronic power assist steering
B+

40A*

Powertrain control module (PCM)
(relay 57 power)

—

Not used

30A*

Starter motor (relay 55 power)

40A*

Rear defrost (relay 53 power)

—

Not used

40A*

Anti-lock Braking System (ABS)
pump

20A*

Wipers washer

30A*

ABS valve

—

Not used

2010 Milan

(mln)

Owners Guide, 1st Printing
USA

(fus)

Roadside Emergencies

239

Summary of Contents for 2010 Milan Hybrid







































































































































































































































































































































Search results

Summary of Contents for 2010 Milan Hybrid

Reviews:

Ford 2010 Milan Hybrid, Owner'S Manual, Page: 239 / 326

Search results

Summary of Contents for 2010 Milan Hybrid

Reviews: