manualshive.com logo in svg

Ford 2010 Milan Hybrid, Owner'S Manual

The Ford 2010 Milan Hybrid is an innovative and eco-friendly sedan that combines the power of a gasoline engine with the efficiency of electric motors. Enhance your driving experience with our Quick Reference Manual, available for free download at manualshive.com, providing essential information to maximize your vehicle's performance.

Share
Download
background image

WARNING:

Position the safety belt height adjusters so that the

belt rests across the middle of your shoulder. Failure to adjust

the safety belt properly could reduce the effectiveness of the safety
belt and increase the risk of injury in a collision.

Safety belt pretensioner

Your vehicle is equipped with safety belt pretensioners at the driver and
front outboard passenger seating positions.

The safety belt pretensioner tightens the safety belts firmly against the
occupant’s body at the start of the crash.

WARNING:

The driver and front passenger safety belt system

(including retractors, buckles and height adjusters) must be

replaced if the vehicle is involved in a collision that results in
deployment of front airbags, seat-mounted side airbags and side air
curtains, and safety belt pretensioners.

Safety belt extension assembly

If the safety belt is too short when fully extended, there is an 8 inch
(20 cm) safety belt extension assembly that can be added (part number
611C22). This assembly can be obtained from an authorized dealer.

Use only extensions manufactured by the same supplier as the safety
belt. Manufacturer identification is located at the end of the webbing on
the label. Also, use the safety belt extension only if the safety belt is too
short for you when fully extended.

WARNING:

Do not use extensions to change the fit of the

shoulder belt across the torso.

Safety belt warning light and indicator chime

The safety belt warning light illuminates in the instrument cluster and a
chime sounds to remind the occupants to fasten their safety belts.

2010 Milan

(mln)

Owners Guide, 1st Printing
USA

(fus)

Seating and Safety Restraints

127

Summary of Contents for 2010 Milan Hybrid







































































































































































































































































































































Reviews:

No comments

Related manuals for 2010 Milan Hybrid

JAC S5 Workshop Manual preview
S5
Brand: JAC Pages: 70
Uniden BTSC1500 Owner'S Manual preview
BTSC1500
Brand: Uniden Pages: 16
Uniden BTSC1500 User Manual preview
BTSC1500
Brand: Uniden Pages: 20
Fab Fours BLACK STEEL S2560 Installation Instructions Manual preview
BLACK STEEL S2560
Brand: Fab Fours Pages: 9
PUTCO MOLLE PANELS RAM 2500 Instruction Manual preview
MOLLE PANELS RAM 2500
Brand: PUTCO Pages: 4
Westfalia Portilo 350000 Installation And Operating Instructions Manual preview
Portilo 350000
Brand: Westfalia Pages: 18
Thule 1511 Instructions Manual preview
1511
Brand: Thule Pages: 8
Audi Q3 2015 - 2019 Technical Service Bulletin preview
Q3 2015 - 2019
Brand: Audi Pages: 12
Hudson 1933 Eight Owner'S Manual preview
1933 Eight
Brand: Hudson Pages: 34
Carcomm CHFS-34 HTC Installation Manual preview
CHFS-34 HTC
Brand: Carcomm Pages: 2
Racelogic Speed & Route Profiler Manual preview
Speed & Route Profiler
Brand: Racelogic Pages: 24
TATA Motors INDICA eV2 XETA CNG Supplemental Owner'S Manual preview
INDICA eV2 XETA CNG
Brand: TATA Motors Pages: 24
PAC AP4-GM61 Quick Start Manual preview
AP4-GM61
Brand: PAC Pages: 5
Percon Falcon 655 User Manual preview
Falcon 655
Brand: Percon Pages: 49
Cadillac ESCALADE ESV 2005 Owner'S Manual preview
ESCALADE ESV 2005
Brand: Cadillac Pages: 482
curt CM-58967 Installation Manual preview
CM-58967
Brand: curt Pages: 4
Mercedes-Benz 2007 SLR Mclaren Operator'S Manual preview
2007 SLR Mclaren
Brand: Mercedes-Benz Pages: 425
CITROËN Jumpy Miltispace Owner'S Handbook Manual preview
Jumpy Miltispace
Brand: CITROËN Pages: 164

Brands by name

Popular brands

Load more brands